Tdm 900 - Oil Pressure : Methods, Ways, Solutions To Measure This Important Data

[chrisr]

Before you go to all that trouble make sure there’s an oil filter properly fitted and the metal sleeve is fitted in the front of the housing with an o-ring. Then put 4 litres of oil in it and see what happens. And make sure you undo the 10 mm oil gallery bolt on the side of the left hand cylinder to check oil flow.

This post was last modified: 24-11-2023, 10:29 PM by chrisr.

[leehenty]

I still have one or two lying around in the workshop you are welcome to one for your project

[Pedro]

A while ago now, (years in fact) I was in contact with someone on here regarding oil pressure adaptors for a 3vd. Stupidly, I deleted all my messages, I cant remember why but there was a reason. Would it be you Leehenty? Apologies if it's you and I stopped replying to messages. I am still interested but I understand if the 3vd ones are all gone. I wish Yamaha at least installed an oil warning light, considering the catastrophic result with running low on oil on an engine that uses it as a finger up to Eco warriors.

[leehenty]

Yes it was me I still have the donor switches. I can make you one on the lathe

[Pedro]

Ooo, yes please! I'm in Spain though so would posting it be a problem?

Also, I've forgotten what's needed. Do I need to get a special oil pressure switch, if so which type? Thanks



Ps. I'm impressed that you can just "make one on the lathe". Some of us mere mortals couldn't make a blunt nail on a lathe.

This post was last modified: 03-12-2023, 08:27 PM by Pedro.

[leehenty]

I Ihave the right donor switch already I can post anywhere in world. Ill get one made and message you

[Pedro]

Ok. Thank you muchly.

[sayhello]

hello you all  hello dear @Pedro, hello dear @leehenty  hello Chrisr 

 

 

 

 

many thanks for the repies. 

 

sorry - was very busy in the last few days - 

 

I still have one or two lying around in the workshop you are welcome to one for your project

 

this would be so awesome. 

 

btw: Pedro lives in Spain - i in Germany - perhaps we can share some parts of the project - guess that it would be very fruitful if we work on the same thing. 

 

 

 

i look forward to hear from you 

 

have a great day

 

 

regards

 

Matze

This post was last modified: 06-12-2023, 10:45 AM by sayhello.

[leehenty]

Dear Mr SayHello,I have brass adapter for an M10x1 NC pressure sensor with 90° to fit a 900 with a custom double banjo bolt. If you would like to pm me with your address

[sayhello]

many thanks dear Leehenty 

 

i have written a PM - i look forward to hear from you. 

 

regards 

 

Say

[sayhello]

dear Leehenty 

 

it would be a great pleasure to hear  from you again.  

 

greetings

[leehenty]

Dear Mr Pedro your switch is made.

[Pedro]

Thank you! I have replied to your PM. Cheers, Pedro

[sayhello]

Dear Leehenty

 

sorry for the delay -   all looks awesome and very very promising. 

i have sent you my postal adress

 

 

have a great day

 

Regards 

[leehenty]

Dear Mr Sayhello your 90° brass adapter has been despatched. Please note you will need to source an M10x 1, normally closed oil pressure switch as described in the JBX-TDM article

This post was last modified: 12-01-2024, 03:39 PM by leehenty.

[Catteeclan]

Snigger

[sayhello]

hi again

 

many many thanks for the reply

 

 

So awesome  - many many thanks!

 

Dear Mr Sayhello your 90° brass adapter has been despatched. Please note you will need to source an M10x 1, normally closed oil pressure switch as described in the JBX-TDM article

 

 

I will digg  into all that. 

 

many thanks..

 

regards 

say

This post was last modified: 25-01-2024, 09:32 AM by sayhello.