Forums › Start your Engine › All About TDM v
Heating Issue

Quadsey
Heating Issue
25
1257
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
Heating Issue

Nig

Member
***
Posts:
220
Threads:
8
Joined:
Mar 2006
Reputation:
0
Ahhh ha - when bleeding the system yesterday I noticed the upper pipe was actually pumping coolant in to the radiator . Never twigged on it was wrong way around. This must be the problem as to why the fan is not cutting in. Going to have to find some in line reducer/ expanding couplings to sort pipe work due to spigot wrong way around.
Aluminium Welding with Parkinson,s
Find
Reply

fixitsan

Posting Freak
*****
Posts:
4,875
Threads:
132
Joined:
Dec 2015
Reputation:
0
Quote:Ahhh ha - when bleeding the system yesterday I noticed the upper pipe was actually pumping coolant in to the radiator . Never twigged on it was wrong way around. This must be the problem as to why the fan is not cutting in. Going to have to find some in line reducer/ expanding couplings to sort pipe work due to spigot wrong way around.

 

I think the fan switch is up with the thermostat body, in the pipework above the rocker cover (below the fuel tank). A shortage of water could mean the fan switch isn't being bathed with coolant. Eventually it probably should still kick in because of the heat from the steam, but I think that direct contact with liquid coolant still works better.

 

The water for the cold start mechanism is plumbed into the lower of the two radiator spigots you already identiified.

 

You're not the first to swap them over ! Smile
<p style="text-align:center;">Ohlins, PC3, fuel cut defeat, +4deg timing, 17" front wheel.
Find
Reply

Nig

Member
***
Posts:
220
Threads:
8
Joined:
Mar 2006
Reputation:
0
That was it just swapped them over and fan cut straight in when towards the red - ran it nearly a full year with pipes around the wrong way - Holy shit what a spanner
Aluminium Welding with Parkinson,s
Find
Reply

agrantg

Posting Freak
*****
Posts:
1,643
Threads:
241
Joined:
Dec 2009
Reputation:
0
Quote:That was it just swapped them over and fan cut straight in when towards the red - ran it nearly a full year with pipes around the wrong way - Holy shit what a spanner

It is not an uncommon problem. Also, they do get quite hot before the fan kicks in but yours is working now, so that's a result.
2004 900 - Blue with lots of goodies

2012 900 - Still adding shiny bits. Was black, changed to white and now back to black again.

 
Find
Reply

peter-may

Posting Freak
*****
Posts:
1,826
Threads:
136
Joined:
Nov 2006
Reputation:
0
Good result there....and FREE!!

My suggestion to just fill the rad and system, in post #2, was aimed at making sure the senders for temp and fan were covered with water. Low water level led to a lot of work on a mini yeeeeears ago. Best lessons are the painful/embarrassing ones!!
Lock onto my co-ordinates and beam me up !!

04 900 - 92 mk 1 - r 1150 rs - Z550 A1 - 2x bonnies - plastic slug -XL185 - ...not in that order !! (and one or two i don't want / dare to own up to !!)
Find
Reply

Nig

Member
***
Posts:
220
Threads:
8
Joined:
Mar 2006
Reputation:
0
Yep agree with you there Mr Picard. Thanks chaps for all you help and input. Really appreciated.
Aluminium Welding with Parkinson,s
Find
Reply


Forum Jump:


Users browsing this thread:
1 Guest(s)