Forums
Cam Chain Tensioner Checks on a 900 - Printable Version

+- Forums (https://www.carpe-tdm.net)
+-- Forum: Start your Engine (https://www.carpe-tdm.net/forumdisplay.php?fid=6)
+--- Forum: KnowledgeBase (https://www.carpe-tdm.net/forumdisplay.php?fid=25)
+---- Forum: Engine, Fluids & Exhausts (https://www.carpe-tdm.net/forumdisplay.php?fid=44)
+---- Thread: Cam Chain Tensioner Checks on a 900 (/showthread.php?tid=31858)

Pages: 1 2 3 4 5

Cam Chain Tensioner Checks on a 900 - dandywarhol - 23-10-2017

The automatic spiral one works fine with the modified (latest post 2006) longer tensioner body



Cam Chain Tensioner Checks on a 900 - Ollyls27 - 22-12-2017

Hi everyone i have a 2003 tdm900 witg 48k on clock, haven't even been out on it yet only ridden it home.ivr started it up today and got a little rattle on the over run so im think it will be the cam chain tensioner, so my question is do i replace for a new one fowlers want £140 or could i replace with a manual one off ebay? Link below



https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F361964489338

Cam Chain Tensioner Checks on a 900 - tdm92 - 30-08-2019

Replaced the CCT at the same time as doing valve shims.  I put in the later type tensioner.  Went to JBX's site for how to set it and site has disappeared!

 

2 questions:

Anyone know if JBX down is permanent?

To set the new tensioner do you pull the tag out directly or rotate and pull?



Cam Chain Tensioner Checks on a 900 - Rallyist - 31-08-2019

Quote:Replaced the CCT at the same time as doing valve shims.  I put in the later type tensioner.  Went to JBX's site for how to set it and site has disappeared!

 

2 questions:

Anyone know if JBX down is permanent?

To set the new tensioner do you pull the tag out directly or rotate and pull?
Link working https://www.tdm-yamaha.heliohost.org/


Cam Chain Tensioner Checks on a 900 - tdm92 - 31-08-2019

Thanks Rallyist.  Works for me too today.  JBX is a good repository of info.

 

The answer: just a straight pull out.  Did that and it set fine.



Cam Chain Tensioner Checks on a 900 - EddTheDuck - 03-01-2023

So I am about to get this done on my 9 at the local Kawasaki dealership for mega bucks! Is it necessary for them to also check the timing hasn't jumped when thye do it or can I get away with just the unit replacement? Cheers for any advice received.



Cam Chain Tensioner Checks on a 900 - Catteeclan - 04-01-2023

When I did mine I got No 1 cylinder at TDC then changed them. The idea is the cam has less chance of moving as inlet and exhaust lobes are getting a bit of contact.

Once replaced always turn the engine over without plugs by hand before trying to start.



Cam Chain Tensioner Checks on a 900 - Trevini - 04-01-2023

I vaguely remember doing the same when I did mine, but it was a long time ago back around 2006/7. Wasn’t the tensioner a recall? I’m pretty sure I didn’t pay for mine at the time.  

 

Edit- just checked and it wasn’t. Only recall was for the tps.



Cam Chain Tensioner Checks on a 900 - EddTheDuck - 04-01-2023

Thanks guys. I'm not totally useless with the spanners and have done various mundane bits myself before like pads, discs, oil changes, brake line replacement and chain and sprockets. However with an engine I am almost a virgin when it comes to stuff inside! I've only ever changed out the oil pump and removed a spinner on my lad's 125 Honda Grom! I'd rather shell out on the CCT job than mess it up!Â