Forums
Anyone Have A Projects On The Go? - Printable Version

+- Forums (https://www.carpe-tdm.net)
+-- Forum: Start your Engine (https://www.carpe-tdm.net/forumdisplay.php?fid=6)
+--- Forum: All About TDM (https://www.carpe-tdm.net/forumdisplay.php?fid=22)
+--- Thread: Anyone Have A Projects On The Go? (/showthread.php?tid=700)

Pages: 1 2 3 4 5


Anyone Have A Projects On The Go? - dapleb - 27-10-2022

Lick lick. ♪┌|∵|┘♪


Anyone Have A Projects On The Go? - leehenty - 28-10-2022

Don't forget that XJ fuel tank needs a proper fix. Brazing would do it


Anyone Have A Projects On The Go? - Studley Ramrod - 28-10-2022

Quote:Don't forget that XJ fuel tank needs a proper fix. Brazing would do it

An opportunity for me to learn a bit about brazing. :good:



Anyone Have A Projects On The Go? - leehenty - 28-10-2022

Mapp gas will be your friend unless you have access to oxy acetylene.


Anyone Have A Projects On The Go? - IrkinBollikans - 28-10-2022

Currently working on learning how to walk again, after my second ride on my tdm ended with major fractures and a new titanium rod in my left leg. Looking forward to getting it repainted and throwing knobby tires on it, once I can get back to work.


Anyone Have A Projects On The Go? - coxylaad - 31-10-2022

Quote:Currently working on learning how to walk again, after my second ride on my tdm ended with major fractures and a new titanium rod in my left leg. Looking forward to getting it repainted and throwing knobby tires on it, once I can get back to work.
 

WTF!



Anyone Have A Projects On The Go? - Snowbird - 31-10-2022

Quote:Currently working on learning how to walk again, after my second ride on my tdm ended with major fractures and a new titanium rod in my left leg. Looking forward to getting it repainted and throwing knobby tires on it, once I can get back to work.

Ouch! Good luck with your recovery. :good:



Anyone Have A Projects On The Go? - IrkinBollikans - 02-11-2022

Quote: 

WTF!


Wet grass and street tires don't mix well. It's been a long five months with more to go, but I'm patiently waiting to start working on my new bike again. Plenty of work to do too. At least for a bike with only 16k miles on the clock...
Quote:Ouch! Good luck with your recovery. :good:


Thank you so much. It's going well I suppose. The boredom is the worst, besides the financial hit.


Anyone Have A Projects On The Go? - Catteeclan - 02-11-2022

Quote:Wet grass and street tires don't mix well. It's been a long five months with more to go, but I'm patiently waiting to start working on my new bike again. Plenty of work to do too. At least for a bike with only 16k miles on the clock...



Thank you so much. It's going well I suppose. The boredom is the worst, besides the financial hit.

Hope all goes well for both you and the bike. I also have had experience of wet grass but not as bad as yours.



Anyone Have A Projects On The Go? - IrkinBollikans - 02-11-2022

Quote:Hope all goes well for both you and the bike. I also have had experience of wet grass but not as bad as yours.


It's crazy that the least severe wreck I've had on a bike, caused the most damage. I've walked away from some gnarly wipeouts, but this is the first time I had to belly crawl away from one. Completely shattered tib/fib about 4" above ankle and also had a clean break just below the knee.


Anyone Have A Projects On The Go? - Sphere - 02-11-2022

Quote:It's crazy that the least severe wreck I've had on a bike, caused the most damage. I've walked away from some gnarly wipeouts, but this is the first time I had to belly crawl away from one. Completely shattered tib/fib about 4" above ankle and also had a clean break just below the knee.
Hope you have a speedy recovery. As we get older, we don't bounce so well.



Anyone Have A Projects On The Go? - coxylaad - 03-11-2022



Quote: The best thing about being old is we did all our stupid stuff before the Internet was invented, so there’s no proof.
 

:rotflmmfao: 




Anyone Have A Projects On The Go? - Catteeclan - 05-11-2022

Quote:It's crazy that the least severe wreck I've had on a bike, caused the most damage. I've walked away from some gnarly wipeouts, but this is the first time I had to belly crawl away from one. Completely shattered tib/fib about 4" above ankle and also had a clean break just below the knee.
Ouch, that’s gonna take some time and work. 



Anyone Have A Projects On The Go? - coxylaad - 13-04-2023

current status:

[Image: IMG-20230219-WA0006.jpg]



Anyone Have A Projects On The Go? - Snowbird - 13-04-2023

Looking good Coxylaad!


Anyone Have A Projects On The Go? - coxylaad - 13-04-2023

ive also started getting into 3d modelling in cad, and the plan is to 3d print a fairing for the bike. 

 

this is where I am up to:

[Image: image.png.4e33afdeab26534167712105cd182b6a.png]

[Image: image.png.54d5ab15bc107c2a54efc2ace6e291d7.png]

[Image: image.png.d0367964e562241d73ea9e9c7995d962.png]

Im trying to create something along the lines of a cross between a Yamaha MT01 and a ducati Diavel



Anyone Have A Projects On The Go? - coxylaad - 13-04-2023

3D printing the prototype parts for the trial fit:

[Image: 20230324_073842.jpg]

[Image: 20230402_165351.jpg.16ce398a8c8eeb059bce...d0fc11.jpg]

 

starting add more detail for the airscoops 

https://youtu.be/UZSXkvuxbS8 

 

[Image: 20230406_174302.jpg]


some smart arse noted that I put the Honda wing on back to front....




Anyone Have A Projects On The Go? - Catteeclan - 13-04-2023

Clever stuff, keep us updated please. :good:




Anyone Have A Projects On The Go? - Snowbird - 13-04-2023

Although I do think nuts bolts and welding would be better than masking tape for holding it all together.... Lol




Anyone Have A Projects On The Go? - dapleb - 13-04-2023

Very clever coxy. Loikey.