+- Forums (https://www.carpe-tdm.net)
+-- Forum: Start your Engine (https://www.carpe-tdm.net/forumdisplay.php?fid=6)
+--- Forum: All About TDM (https://www.carpe-tdm.net/forumdisplay.php?fid=22)
+--- Thread: Winter Project (/showthread.php?tid=3018)
Winter Project - alanfavell - 15-03-2019
Lovely - quite envious :good:
Winter Project - ramotdm - 15-03-2019
Nice, you're doing great job mate :good:
Winter Project - Studley Ramrod - 15-03-2019
Ooooh, sminky pipes, very lickable. :good:Â
Â
Quote:Studz are yew referring to basket replacement on a TDM 900 or and 850 as i'd not heard of 9er basket problems?Â
I think it was a 9'er basket that lunched itself, broke a tang or two and mashed the clutch plates iirc. Could be wrong though Ken.
Winter Project - coxylaad - 16-03-2019
Fitted. Need to make up a link pipe, shouldnt be a problem
Â
![[Image: uC4knC5.jpg]](https://i.imgur.com/uC4knC5.jpg)
Â
![[Image: wAOQ32H.jpg]](https://i.imgur.com/wAOQ32H.jpg)
Â
I fired it up this morning. good news, brand new ecu and it fired up first time and settled down to a tickover, with no end cans on it sounded like a top fuel drag racer.Â
Â
good stuff
Winter Project - wicklamulla - 16-03-2019
Coxxy is the ECU stock or flashed like Fixitsans?
Winter Project - coxylaad - 17-03-2019
None of the above its a standalone unit from a company called Ignitech. Amazing that it's just fired straight up being so bespoke
Winter Project - wicklamulla - 17-03-2019
Quote:None of the above its a standalone unit from a company called Ignitech. Amazing that it's just fired straight up being so bespokeÂ
Â
I know i shud re-read the fred but are those doonpoipes & link poipes stock or over sized? They look amazing.
Winter Project - coxylaad - 17-03-2019
They start 38mm and increase to 42mm halfway down the down pipes. Bit like the trx akra headers
Winter Project - Studley Ramrod - 17-03-2019
It's aliiiiiiiiive !
 Good job Coxy.Winter Project - dandywarhol - 17-03-2019
Did these pipes come via Kayla?
Winter Project - fixitsan - 18-03-2019
Great progress !
Winter Project - coxylaad - 19-03-2019
Quote:Did these pipes come via Kayla?
No they came via Greece!
Winter Project - coxylaad - 22-03-2019
anyone know if the tdm 900 shares the same rear caliper as any other bike in the range? i cant find one it seems unique which is odd for yamaha.
The 2000 r6 looks like similar fittings and might work but its a gamble. plus i have just fitted a piston and seal kit to this on that I have just destroyed (cracked at the bleed nipple)
ideally i would like a stock replacement if anyone is selling one.
Winter Project - ramotdm - 23-03-2019
Don't think it does, TDM 900 02-10 only (non ABS)
Winter Project - Studley Ramrod - 23-03-2019
Loads for sale here Coxy. https://www.gn-moto.com/158-900tdm-2002-2011?p=2
Winter Project - coxylaad - 23-03-2019
new exhaust end can position:
![[Image: 8zLOy2N.jpg]](https://i.imgur.com/8zLOy2N.jpg)
![[Image: zzDEZaK.jpg]](https://i.imgur.com/zzDEZaK.jpg)
![[Image: 7QmcpUa.jpg]](https://i.imgur.com/7QmcpUa.jpg)
its a little more aggressively angled than the normal tdm end cans but i think it works really well with the lines of the bike.
new link pipes
![[Image: VmSyRPS.jpg]](https://i.imgur.com/VmSyRPS.jpg)
i think i am just going to weld them up so the link pipe to the end can is one piece with the header. i dont see the point of having clamps and stuff there when its never going to move.
Winter Project - dablik - 24-03-2019
Looks quite close to the pannier in the photo coxy ! i had Laser Duo Tech on an old 9r at approx the same angle, put some silver self adhesive foil on the bottoms of them just in case and had no issues at all with heat from the exhaust.
Winter Project - alanfavell - 24-03-2019
I'm with Dablik here - 1978 I toasted my fiberglass Craven panniers (one side only - but twin cans - wtf), melted my sleeping bag and toothbrush - IÂ found out after I put up my tent in Dijon.Â
Winter Project - drewpy - 24-03-2019
Looking good so far
Winter Project - dandywarhol - 24-03-2019
Crack on lad - winter's over.........................................